eu.warwickts.com

W-FSA-2RAB Banana Plug Adapter Lead for Bosch FSA

W-FSA-2RAB Banana Plug Adapter Lead for Bosch FSA A replacement banana plug adapter lead for Bosch FSA500. Suitable alternative for Bosch 1684463522, ADAPTER LINE. Consists of a 6 pin male connector to interface with the FSA500 and dual right angled banana plugs to enable connection to current clamps and other diagnostic test connections.

W-FSA-6RAB 6 Way Banana Plug Adapter Lead for Bosch FSA

W-FSA-6RAB 6 Way Banana Plug Adapter Lead for Bosch FSA A 6 way banana plug adapter lead for Bosch FSA500. Consists of a 6 pin male connector to interface with the FSA500 and six right angled banana plugs to enable connection to current clamps and other diagnostic test connections.

WBDCM-8 8 Channel Bulkhead BNC Diagnostic Cart Mounting Kit

8 Channel Oscilloscope Bulkhead BNC Diagnostic Cart Mounting Kit Automotive oscilloscopes such as the Picoscope are delicate instruments that are not cheap to replace if damaged, especially the newer 8 channel variants. How many close calls have you had balancing a scope on a vehicle, hanging it from the bonnet or snagging its leads pulling the scope or toppling it off a bench or cart? This is where the WBDCM-8 comes to fruition, enabling ultimate protection for your 8 channel scope. The WBDCM-8 is a BNC bulkhead mounting kit which allows you to safely store your oscilloscope in a draw or shelf of a diagnostic cart or toolbox protecting it from damage and dirt. The kit mounts to the front or side of your cart/box and provides BNC connections and patch leads to connect your oscilloscope on the inside and BNC connections on the outside to connect your long leads. When long leads are not connected protective covers are used to cover the BNC connections protecting them from dirt, knocks and damage. The WBDCM-8 kit consists of: A BNC Bulkhead Plate with BNC connections which is mounted to the diagnostic cart or toolbox using six M3 socket cap screws; A set of eight colour coded BNC patch leads to connect to the inside BNC bulkhead connector and your oscilloscope; Two protective covers for the front of the bulkhead plate. Each provides protection for four channels so a cover can remain in place should you only need four or less channels. Features: BNC Bulkhead Plate easily mounted and secured to a diagnostic cart or toolbox with six M3 socket cap screws. You will need to drill four M3 and eight 13mm holes in the cart/box. BNC bulkhead connectors are insulated from the diagnostic cart. Patch leads use fully shielded 50 Ohm cable, IEC 601010 rated BNC connectors and have colour coded insulated BNC connector jackets to match the input colours of the oscilloscope. Protective covers gives protection to the BNC connections from dirt and damage when leads are not connected and in use. Can be easily removed and mounted again when its time for a new diagnostic cart. The protective cover is available in different colours to suit your cart and the patch leads are available in different lengths. Make your selections using the dropdown boxes. We can also make custom length patch leads if the standard lengths don't suit you, please contact us. Due to the customisation of this product we manufacture them to order, so expect a short lead time. Also note that an order can not be cancelled once production has begun and is non refundable.

WBDCM-4 Bulkhead BNC Diagnostic Cart Mounting Kit

Oscilloscope Bulkhead BNC Diagnostic Cart Mounting Kit Automotive oscilloscopes such as the Picoscope are delicate instruments that are not cheap to replace if damaged. How many close calls have you had balancing the scope on a vehicle, hanging it from the bonnet or snagging its leads pulling the scope or toppling it off a bench or cart? This is where the WBDCM-4 comes to fruition, enabling ultimate protection for your scope. Designed in collaboration with Jarhead Diagnostics, the WBDCM-4 is a BNC bulkhead mounting kit which allows you to safely store your oscilloscope in a draw or shelf of a diagnostic cart or toolbox protecting it from damage and dirt. The kit mounts to the front or side of your cart/box and provides BNC connections and patch leads to connect your oscilloscope on the inside and BNC connections on the outside to connect your long leads. When the long leads are not connected the protective cover is used to cover the BNC connections protecting them from dirt, knocks and damage. The WBDCM-4 kit consists of: A BNC Bulkhead Plate with BNC connections which is mounted to the diagnostic cart or toolbox using four M3 socket cap screws; A set of four colour coded BNC patch leads to connect to the inside BNC bulkhead BNC connector and your oscilloscope; A protective cover for the front of the bulkhead plate. Features: BNC Bulkhead Plate easily mounted and secured to a diagnostic cart or toolbox with four M3 socket cap screws. You will need to drill four M3 and four 13mm holes in the cart/box. BNC bulkhead connectors are insulated from the diagnostic cart. Patch leads use fully shielded 50 Ohm cable and are colour coded to match the input colours of the oscilloscope and OEM leads. Patch leads use fully insulated IEC 601010 rated BNC connectors. Protective cover gives protection to the BNC connections from dirt and damage when leads are not connected and in use. Can be easily removed and mounted again when its time for a new diagnostic cart. The protective cover is available in different colours to suit your cart and the patch leads are available in different lengths. Make your selections using the dropdown boxes. We can also make custom length patch leads if the standard lengths don't suit you, please contact us. Picoscope Mounted Tiepie Automotive Oscilloscope Mounted. Due to the customisation of this product we manufacture them to order, so expect a short lead time. Also note that an order can not be cancelled once production has begun and is non refundable.

WTS-BNC-CR3-7 3.7mm BNC Lead Cable Clamp Set

WTS-BNC-CR3-7 BNC Lead Cable Clamps This BNC Lead Cable Clamp set consists of a 4 x 4 way friction clamps designed to be used with BNC leads of 3.7mm Outside Diameter (OD). The clamp has double magnets mounted on the rear to enable them to be secured against a metal object. The magnets combined have a pulling force of 1.8kg. The clamps are ideal for use in an automotive environment with our 7086 BNC oscilloscope leads, MODIS 3m Scope Leads or those provided with the range of Picoscope automotive oscilloscopes. Amp Clamp Options Also available is an additional clamp piece that fits into one of the clamp jaws that will enable the clamping of cables from either a Pico amp clamp, Pico+ amp clamp or a SnapOn amp clamp. Two amp clamp pieces are supplied when ordered. Select option by using the drop down box. The clamp clamp allows each cable to be pressed into its jaws securing it in place by means of a friction fit. Using these clamps enables you to keeps your cables tidy and out of the way of harmful moving engine parts or becoming a trip hazard when using long 3m or 5m meter leads. It also enables you to conduct short test drives with connections in place. Note that the clamps should not be placed on to hot surfaces. The colour of product may vary.

Split Ground Lead

Split Ground Lead to Combine multiple Ground Connections This lead is designed to make multiple ground connections safer and easier when using multiple channels on the automotive lab scopes. The lead is constructed using flexible wear indicating test lead cable and IEC rated Banana Plug and Sockets to ensure quality ground connections. At the single connection end end there is a 4mm banana plug to make the connection to a lab scope ground socket. At the other end are four straight 4mm banana sockets which allow you to connect up to four 4mm banana plug ground leads. This lead remotes the ground connection away from the body of the lab scope so you don't have awkward stacked grounds extending out the top of the scope waiting to be damaged. This lead has two variations. 30cm - Ideal for short remoting of your lab scope ground connection. 3m - Ideal for connecting a multiple ground using the vehicle battery negative terminal or a common ground on a vehicle.

MODIS 3m Shielded Red Scope Test Lead

MODIS-R-3M Shielded Blue Scope Test lead 3m for Snap-on MODIS This lead is designed as longer replacement red lead for your Snap-on MODIS lab scope with an overall length of 3m. The lead is constructed using fully shielded flexible cable to protect your signal from noise. At the scope end there is a right angled banana plug to make the connection to the channel along with a ground lead stacking banana plug. At the other end is straight shrouded 4mm banana plugs. One to connect to your test connection such as alligator clips, piercing probes or other connectors and the other to connect to ground within the vehicle. The Red test lead is designed to connect to channel other than channel one on the lab scope. It is recommended that the MODIS-Gd lead is used with this cable to enable safe and practical stacking connection of the scope ground. This 3m lead gives you plenty of room to conduct scope diagnostics during a test drive or to have the lab scope on a cart away from the vehicle. This lead forms part of the MODIS 3m Lead Set.

MODIS Shielded Yellow Scope Test Lead (Ch1)

MODIS-Y-3M Shielded Yellow Scope Test lead (Ch1) for Snap-on MODIS This lead is designed as longer replacement yellow lead for your Snap-on MODIS lab scope with an overall length option of 3m or 5m. The lead are constructed using fully shielded flexible cable to protect your signal from noise. At the scope end there is a right angled banana plug to make the connection to the channel along with a ground lead stacking banana plug. At the other end is straight shrouded 4mm banana plugs. One to connect to your test connection such as alligator clips, piercing probes or other connectors and the other to connect to ground within the vehicle. The Yellow lead is designed to connect to channel one on the lab scope and has a ground lead to make the common ground connection on the vehicle. It is recommended that the MODIS-Gd lead is paired with this cable to enable safe and practical stacking connection of the scope ground. This 3m lead gives you plenty of room to conduct scope diagnostics during a test drive or to have the labscope on a cart away from the vehicle. This lead forms part of the MODIS 3m Lead Set.

MODIS Shielded Scope Lead Set

MODISSET Shielded Scope Test lead set 3m or 5m for Snap-on MODIS, VERSUS, VANTAGE and ZEUS This lead set is designed as longer replacement leads for your Snap-on MODIS, VERSUS, VANTAGE and ZEUS lab scope with an overall length of 3m or 5m. The leads are constructed using fully shielded flexible cable to protect your signal from noise. They have right angled banana plugs at one end to make the connection to the scope a ground lead stacking banana plug and a straight shrouded 4mm banana plug at the other end to connect to your test connection such as alligator clips, piercing probes or other connectors. One of the issues of the OEM test leads is the length is not long enough to enable you to conduct test drives or to have the lab scope on a cart away from the vehicle. These test leads give plenty of length allowing the scope to be inside the vehicle during a test drive or for the MODIS, VERSUS, VANTAGE or ZEUS to be located on a diagnostic cart away at a distance from the vehicle. The Yellow lead is designed to connect to channel one on the lab scope and has a ground lead to make the common ground connection on the vehicle. Included is a short 4mm right angled banana plug to straight 4mm banana plug lead to enable you to safely stack the ground connections out of the way instead of the usual requirement to stack on top of the scope. 3m Scope leads are available separately: Yellow Lead Green Lead Blue Lead Red Lead Ground extension

MODIS Ground Lead for safe stacking

MODIS-Gd Shielded Ground Lead to Safely Stack Ground Connections for Snap-on MODIS This lead is designed to make stacking ground connections safer and easier when using multiple channels on the Snap-on MODIS lab scope. The lead is constructed using fully shielded flexible wear indicating cable to protect your signal from noise. At the scope end there is a right angled banana plug to make the connection to the ground socket. At the other end is a straight 4mm banana plug which plugs straight into a stack of banana plugs. This lead remotes the ground connection away from the body of the MODIS so you don't have awkward stacked grounds extending out the top of the scope waiting to be damaged. This lead forms part of the MODIS 3m Lead Set.

MODIS Shielded Green Scope Test Lead (Ch2)

MODIS-G-3M Shielded Green Scope Test lead (Ch2) for Snap-on MODIS This lead is designed as longer replacement green lead for your Snap-on MODIS lab scope with an overall length option of 3m or 5m. The lead is constructed using fully shielded flexible cable to protect your signal from noise. At the scope end there is a right angled banana plug to make the connection to the channel along with a ground lead stacking banana plug. At the other end is straight shrouded 4mm banana plugs. One to connect to your test connection such as alligator clips, piercing probes or other connectors and the other to connect to ground within the vehicle. The Green test lead is designed to connect to channel other than channel one on the lab scope. It is recommended that the MODIS-Gd lead is used with this cable to enable safe and practical stacking connection of the scope ground. This 3m lead gives you plenty of room to conduct scope diagnostics during a test drive or to have the lab scope on a cart away from the vehicle. This lead forms part of the MODIS 3m Lead Set.

MODIS 3m Shielded Blue Scope Test Lead

MODIS-B-3M Shielded Blue Scope Test lead 3m for Snap-on MODIS This lead is designed as longer replacement blue lead for your Snap-on MODIS lab scope with an overall length of 3m. The lead is constructed using fully shielded flexible cable to protect your signal from noise. At the scope end there is a right angled banana plug to make the connection to the channel along with a ground lead stacking banana plug. At the other end is straight shrouded 4mm banana plugs. One to connect to your test connection such as alligator clips, piercing probes or other connectors and the other to connect to ground within the vehicle. The Blue test lead is designed to connect to channel other than channel one on the lab scope. It is recommended that the MODIS-Gd lead is used with this cable to enable safe and practical stacking connection of the scope ground. This 3m lead gives you plenty of room to conduct scope diagnostics during a test drive or to have the lab scope on a cart away from the vehicle. This lead forms part of the MODIS 3m Lead Set.

3m Shielded Oscilloscope Test Lead Set for ATS EScope

WES-3M Shielded Oscilloscope Test lead set - 3m for ATS EScope This lead is designed as a replacement lead set for your ATS EScope lab scope with an overall length of 3m. The leads are manufactured using fully shielded flexible cable to protect your signal from noise. At the scope end there is a safety BNC Connector to make the connection to the channel along with a stacking 4mm banana plug on the other end to be able to connect to a range of test connections such as alligator clips, piercing probes or other connectors. An additional 3m ground lead using stacking banana plugs is also included to enable easy connection to the scope and vehicle battery ground.

WSRAL20M 12A PVC Test Lead With Shrouded Banana Plugs

WSRAL20M 12A PVC Test Leads With Shrouded Banana Plugs The bespoke Multimeter Lead features a 4mm stacking shrouded banana plug and 4mm right angled shrouded banana plug on 20m of 12A test lead. The Multimeter Lead is 0.75mm² (18AWG) and PVC insulated. The test lead comes in various colours. Also available in a pair of Red and Black leads Voltage Rating of 1000V CATII/ 600V CATIII Current Rating of 12 A

WAUT-CS Crocodile Clip to 4mm Socket 36A Test Lead

WAUT-CS Crocodile Clip to 4mm Banana Socket 36A Test Lead The bespoke test lead features a PJP 1065 4mm shrouded banana socket and PJP 5066-IEC 4mm Stacking Shrouded Banana Plugs. The test lead is 2.50 mm² (3.9 mm O/D) - 36A PVC insulated. The test lead comes in black/red, and available in either 3M or 5M lengths to meet your diagnostic application. Specification Set includes: 1 × Red Lead and 1 × Black Lead Voltage Rating of < 33 V AC < 70 V DC Current Rating of 36A Made to Order.

Shielded BNC to 4mm Banana Plug Oscilloscope Lead Set 1089 Variant

Shielded BNC to 4mm Banana Plug Oscilloscope Lead Set A set of shielded BNC to 4mm Stacking Banana Plug leads. Manufactured by us using a specially designed highly flexible shielded cable and quality Electro-PJP parts. The cable is a smaller diameter (3.7mm) than RG 58 providing greater flexibility and mechanical features than standard RG58 cable. These leads are fitted with PJP 1086 Retractable Stacking banana plugs rather than the standard 1076. A great quality lead set for automotive technicians who require extra length when using an oscilloscope or other diagnostic equipment that use a BNC connection for vehicle diagnostics such as: Hantek automotive diagnostic oscilloscope Picoscope automotive oscilloscope Autel MaxiScope Sealey automotive diagnostic oscilloscope Draper diagnostic oscilloscope Siglent handheld oscilloscope UNI-T handheld oscilloscope Available in 3m lengths. Other lengths available, contact for details and pricing. Note: Our BLUE BNC cable is no longer available so the blue lead will be black cable with blue BNC and Blue banana plugs

ChassisEar BNC to 3.5mm Inline Socket Oscilloscope Lead Set

Shielded BNC to 3.5mm Inline Socket Chassisears/Oscilloscope Lead Set - 3m A set of 3m shielded BNC to 3.5mm inline socket leads for use with the ChassisEars diagnostics system part numbers 06600 and 06610 enabling noise diagnostics with an Oscilloscopes. Manufactured by us using a specially designed highly flexible shielded cable and quality Electro-PJP parts. The cable is a smaller diameter (3.7mm) than RG 58 providing greater flexibility and mechanical features than standard RG58 cable. Ensure your ChassisEar mic Clips have this connection: A great quality lead set for automotive technicians who wish to use their Chassis Ears microphone clip set with their automotive oscilloscope, such as: Hantek automotive diagnostic oscilloscope Picoscope automotive oscilloscope Autel MaxiScope ATS Scopes Siglent handheld oscilloscope Bespoke lengths such as 8m and 10m available, please contact us. MADE TO ORDER

ChassisEar BNC to RCA Inline Socket Oscilloscope Lead Set

Shielded BNC to RCA Inline Socket Chassisears/Oscilloscope Lead Set - 3m A set of 3m shielded BNC to RCA inline socket leads for use with the 97202 Wireless ChassisEAR diagnostics system enabling noise diagnostics with an Oscilloscopes. Manufactured by us using a specially designed highly flexible shielded cable and quality Electro-PJP parts. The cable is a smaller diameter (3.7mm) than RG 58 providing greater flexibility and mechanical features than standard RG58 cable. Ensure your ChassisEar Mic Clips have this connection: A great quality lead set for automotive technicians who wish to use their Chassis Ears microphone clip set with their automotive oscilloscope, such as: Hantek automotive diagnostic oscilloscope Picoscope automotive oscilloscope Autel MaxiScope ATS Scopes Siglent handheld oscilloscope Bespoke lengths such as 5m and 10m available, please contact us. MADE TO ORDER

Shielded BNC to 4mm Banana Plug Oscilloscope Lead Set

Shielded BNC to 4mm Banana Plug Oscilloscope Lead Set A set of shielded BNC to 4mm Stacking Banana Plug leads. Manufactured by us using a specially designed highly flexible shielded cable and quality Electro-PJP parts. The cable is a smaller diameter (3.7mm) than RG 58 providing greater flexibility and mechanical features than standard RG58 cable. A great quality lead set for automotive technicians who require extra length when using an oscilloscope or other diagnostic equipment that use a BNC connection for vehicle diagnostics such as: Hantek automotive diagnostic oscilloscope Picoscope automotive oscilloscope Autel MaxiScope Sealey automotive diagnostic oscilloscope Draper diagnostic oscilloscope Siglent handheld oscilloscope UNI-T handheld oscilloscope Available in stock - 3m or 5m lengths. Bespoke lengths such as 8m and 10m available, please contact us. Note: Our BLUE BNC cable is no longer available so the blue lead will be black cable with blue BNC and Blue banana plugs Also available as individual replacement leads: BNC to 4mm Banana Plugs 3m BNC to 4mm Banana Plugs 5m

Set of 4 Insulated BNC Male 50 Ohm Cables 1.5m

Insulated BNC (M) 50 Ohm Cable Set - Automotive Oscilloscope Patch Leads Set of BNC Male to BNC Male 50Ω Cables with 4 different coloured insulated connectors length 150cm. Conform to IEC 61010-1/61010-031 Original component parts from european manufacturer - Electro-PJP This item is available with discounts for bulk purchases.